P0316 on Chrysler 300
Factory diagnostic protocol and troubleshooting wire for fault code P0316 specifically for the Chrysler 300 (2020–2025, 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)).
1. Symptoms of P0316 on Chrysler 300
When the Engine Control Module (ECM/PCM) on your Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)) logs fault code P0316, drivers commonly observe:
2. Most Likely Causes on Chrysler 300
Historical warranty claims and technical repair bulletins for Chrysler 300 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler 300
Check if P0316 is accompanied by a specific cylinder code (like P0303) to isolate which cylinder is misfiring on startup. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Pressurize cold cooling system to 15 PSI. Use a borescope camera through spark plug hole to check for coolant pool on piston top. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Remove spark plugs. Check for white coolant crust, fuel fouling, or cracked ceramic insulators. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
On direct-injection engines, perform walnut shell blasting or chemical intake valve cleaning to remove cold carbon buildup. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Clear DTCs and allow vehicle to sit overnight to confirm morning start is clean. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Equipment for Diagnosing Chrysler 300 (P0316)
Chrysler 300 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Chrysler 300.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chrysler 300
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler 300:
4. Chrysler 300 P0316 FAQs
What causes code P0316 to trigger on a Chrysler 300?
On the Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)), P0316 is most frequently caused by Coolant leaking into cylinder overnight from failing head gasket or intake manifold or Leaking fuel injector dripping fuel into cylinder while parked.
Where is the OBD-II port located on my Chrysler 300?
On the Chrysler 300, the 16-pin DLC diagnostic connector is located Under driver side dash near left knee panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler 300 with code P0316?
Caution. Engine misfires heavily for the first 30–60 seconds after starting, then smooths out. Given that P0316 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.