P0155 on Chrysler 300
Factory diagnostic protocol and troubleshooting wire for fault code P0155 specifically for the Chrysler 300 (2020–2025, 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)).
1. Symptoms of P0155 on Chrysler 300
When the Engine Control Module (ECM/PCM) on your Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)) logs fault code P0155, drivers commonly observe:
2. Most Likely Causes on Chrysler 300
Historical warranty claims and technical repair bulletins for Chrysler 300 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler 300
Inspect the O2 HTR fuse in the engine fuse box with a test light or multimeter. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Unplug the sensor connector and measure resistance between the two heater pins. An open circuit (infinite ohms / OL) confirms a dead internal heater. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Remove faulty sensor and install a new OEM oxygen sensor with built-in heater. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Clear DTCs and allow engine to cool down, then restart to confirm P0155 does not return. on the Chrysler 300 equipped with 3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8).
Equipment for Diagnosing Chrysler 300 (P0155)
Chrysler 300 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Chrysler 300.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chrysler 300
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler 300:
4. Chrysler 300 P0155 FAQs
What causes code P0155 to trigger on a Chrysler 300?
On the Chrysler 300 (3.6L Pentastar V6 (292HP) / 5.7L / 6.4L 392 HEMI V8 (485HP SRT8)), P0155 is most frequently caused by Burnt-out heating element inside the Bank 2 Sensor 1 O2 sensor or Blown O2 heater fuse in under-hood fuse block.
Where is the OBD-II port located on my Chrysler 300?
On the Chrysler 300, the 16-pin DLC diagnostic connector is located Under driver side dash near left knee panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler 300 with code P0155?
Yes. The sensor will take longer to warm up, causing brief open-loop fuel delay on cold starts. Given that P0155 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.