P0137 on Jeep Gladiator
Factory diagnostic protocol and troubleshooting wire for fault code P0137 specifically for the Jeep Gladiator (2020–2026, 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave).
1. Symptoms of P0137 on Jeep Gladiator
When the Engine Control Module (ECM/PCM) on your Jeep Gladiator (3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave) logs fault code P0137, drivers commonly observe:
2. Most Likely Causes on Jeep Gladiator
Historical warranty claims and technical repair bulletins for Jeep Gladiator point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Jeep Gladiator
Listen for exhaust ticking or black soot around flex pipe, flanges, and sensor bungs before the catalytic converter. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Monitor B1S2 voltage. Snap the throttle to enrich mixture; voltage should briefly spike above 0.8V. If it remains 0.0V–0.1V, sensor is defective or shorted. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Unplug harness, remove old sensor with 7/8 socket, install replacement sensor and plug firmly. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Clear DTCs and verify B1S2 holds steady between 0.45V and 0.75V during steady highway cruising. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Equipment for Diagnosing Jeep Gladiator (P0137)
Jeep Gladiator OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Jeep Gladiator.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Jeep Gladiator
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Jeep Gladiator:
4. Jeep Gladiator P0137 FAQs
What causes code P0137 to trigger on a Jeep Gladiator?
On the Jeep Gladiator (3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave), P0137 is most frequently caused by Exhaust leak upstream of or directly at the Sensor 2 bung letting in fresh air or Faulty downstream oxygen sensor.
Where is the OBD-II port located on my Jeep Gladiator?
On the Jeep Gladiator, the 16-pin DLC diagnostic connector is located Under driver dash near left knee kick panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Jeep Gladiator with code P0137?
Yes. Vehicle is fully drivable, but Check Engine Light will remain illuminated. Given that P0137 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.