P0137 on Dodge Challenger
Factory diagnostic protocol and troubleshooting wire for fault code P0137 specifically for the Dodge Challenger (2020–2026, 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)).
1. Symptoms of P0137 on Dodge Challenger
When the Engine Control Module (ECM/PCM) on your Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)) logs fault code P0137, drivers commonly observe:
2. Most Likely Causes on Dodge Challenger
Historical warranty claims and technical repair bulletins for Dodge Challenger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Challenger
Listen for exhaust ticking or black soot around flex pipe, flanges, and sensor bungs before the catalytic converter. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Monitor B1S2 voltage. Snap the throttle to enrich mixture; voltage should briefly spike above 0.8V. If it remains 0.0V–0.1V, sensor is defective or shorted. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Unplug harness, remove old sensor with 7/8 socket, install replacement sensor and plug firmly. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Clear DTCs and verify B1S2 holds steady between 0.45V and 0.75V during steady highway cruising. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Equipment for Diagnosing Dodge Challenger (P0137)
Dodge Challenger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Challenger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Challenger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Challenger:
4. Dodge Challenger P0137 FAQs
What causes code P0137 to trigger on a Dodge Challenger?
On the Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)), P0137 is most frequently caused by Exhaust leak upstream of or directly at the Sensor 2 bung letting in fresh air or Faulty downstream oxygen sensor.
Where is the OBD-II port located on my Dodge Challenger?
On the Dodge Challenger, the 16-pin DLC diagnostic connector is located Under driver dash left of center stack. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Challenger with code P0137?
Yes. Vehicle is fully drivable, but Check Engine Light will remain illuminated. Given that P0137 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.