B0091 on Dodge Challenger
Factory diagnostic protocol and troubleshooting wire for fault code B0091 specifically for the Dodge Challenger (2020–2026, 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)).
1. Symptoms of B0091 on Dodge Challenger
When the Engine Control Module (ECM/PCM) on your Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)) logs fault code B0091, drivers commonly observe:
2. Most Likely Causes on Dodge Challenger
Historical warranty claims and technical repair bulletins for Dodge Challenger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Challenger
Disconnect battery negative cable and wait 15 minutes to fully discharge SRS backup capacitors before touching airbag components. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Remove driver side door sill trim / lower B-pillar trim to access the yellow impact sensor. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Inspect sensor for water corrosion or cracked plastic housing. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Bolt new OEM side impact sensor into clean, rust-free ground location, torque bolt to spec, and click yellow locking connector firmly. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Reconnect battery, clear SRS trouble codes with an airbag-capable scanner, and verify light turns off after 5-second bulb check. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Equipment for Diagnosing Dodge Challenger (B0091)
Dodge Challenger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Challenger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Challenger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Challenger:
4. Dodge Challenger B0091 FAQs
What causes code B0091 to trigger on a Dodge Challenger?
On the Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)), B0091 is most frequently caused by Corroded or damaged left side impact crash sensor (B-pillar or door sill) or Corroded wiring harness under driver seat / driver door sill.
Where is the OBD-II port located on my Dodge Challenger?
On the Dodge Challenger, the 16-pin DLC diagnostic connector is located Under driver dash left of center stack. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Challenger with code B0091?
Caution. Side curtain and seat airbag deployment may be disabled in a side-impact collision. Given that B0091 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.