B1325 on Toyota Camry TRD: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code B1325 (B1325: Device Power 1 Circuit Voltage Below Threshold (BCM)) specifically on the Toyota Camry TRD (2020–2025, 3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust)).
1. Symptoms of B1325 on Toyota Camry TRD
When the Engine Control Module (ECM/PCM) on your Toyota Camry TRD (3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust)) logs fault code B1325, drivers commonly observe:
2. Most Likely Causes on Toyota Camry TRD
Historical warranty claims and technical repair bulletins for Toyota Camry TRD point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Toyota Camry TRD
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether B1325 is static or intermittent. on the Toyota Camry TRD equipped with 3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust).
Visually inspect the physical component (Main BCM Ground Wire), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Toyota Camry TRD equipped with 3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Toyota Camry TRD equipped with 3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Toyota Camry TRD equipped with 3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Toyota Camry TRD equipped with 3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust).
Other Common Fault Codes on Toyota Camry TRD
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Toyota Camry TRD:
4. Toyota Camry TRD B1325 FAQs
What causes code B1325 to trigger on a Toyota Camry TRD?
On the Toyota Camry TRD (3.5L V6 DOHC 24V with Dual VVT-i (301 HP / TRD Cat-Back Exhaust)), B1325 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Main BCM Ground Wire) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Toyota Camry TRD?
On the Toyota Camry TRD, the 16-pin DLC diagnostic connector is located Driver footwell lower knee bolster panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Toyota Camry TRD with code B1325?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that B1325 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.