B0091 on Lexus RX
Factory diagnostic protocol and troubleshooting wire for fault code B0091 specifically for the Lexus RX (2020–2026, 2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP)).
1. Symptoms of B0091 on Lexus RX
When the Engine Control Module (ECM/PCM) on your Lexus RX (2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP)) logs fault code B0091, drivers commonly observe:
2. Most Likely Causes on Lexus RX
Historical warranty claims and technical repair bulletins for Lexus RX point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Lexus RX
Disconnect battery negative cable and wait 15 minutes to fully discharge SRS backup capacitors before touching airbag components. on the Lexus RX equipped with 2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP).
Remove driver side door sill trim / lower B-pillar trim to access the yellow impact sensor. on the Lexus RX equipped with 2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP).
Inspect sensor for water corrosion or cracked plastic housing. on the Lexus RX equipped with 2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP).
Bolt new OEM side impact sensor into clean, rust-free ground location, torque bolt to spec, and click yellow locking connector firmly. on the Lexus RX equipped with 2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP).
Reconnect battery, clear SRS trouble codes with an airbag-capable scanner, and verify light turns off after 5-second bulb check. on the Lexus RX equipped with 2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP).
Equipment for Diagnosing Lexus RX (B0091)
Lexus RX OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Lexus RX.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Lexus RX
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Lexus RX:
4. Lexus RX B0091 FAQs
What causes code B0091 to trigger on a Lexus RX?
On the Lexus RX (2.4L Turbo (RX 350 275HP) / 2.5L Hybrid / 2.4L Turbo Performance Hybrid (RX 500h 366HP)), B0091 is most frequently caused by Corroded or damaged left side impact crash sensor (B-pillar or door sill) or Corroded wiring harness under driver seat / driver door sill.
Where is the OBD-II port located on my Lexus RX?
On the Lexus RX, the 16-pin DLC diagnostic connector is located Driver footwell above brake pedal assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Lexus RX with code B0091?
Caution. Side curtain and seat airbag deployment may be disabled in a side-impact collision. Given that B0091 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.