P0335 on Jeep Wrangler: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0335 (P0335: Crankshaft Position Sensor A Circuit Malfunction) specifically on the Jeep Wrangler (2020–2026, 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP)).
1. Symptoms of P0335 on Jeep Wrangler
When the Engine Control Module (ECM/PCM) on your Jeep Wrangler (3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP)) logs fault code P0335, drivers commonly observe:
2. Most Likely Causes on Jeep Wrangler
Historical warranty claims and technical repair bulletins for Jeep Wrangler point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Jeep Wrangler
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0335 is static or intermittent. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Visually inspect the physical component (Crankshaft Position (CKP) Sensor), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Jeep Wrangler equipped with 3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP).
Other Common Fault Codes on Jeep Wrangler
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Jeep Wrangler:
4. Jeep Wrangler P0335 FAQs
What causes code P0335 to trigger on a Jeep Wrangler?
On the Jeep Wrangler (3.6L Pentastar V6 / 2.0L Turbo 4-Cyl / 4xe Hybrid (375HP) / 6.4L 392 HEMI (470HP)), P0335 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Crankshaft Position (CKP) Sensor) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Jeep Wrangler?
On the Jeep Wrangler, the 16-pin DLC diagnostic connector is located Below steering wheel near driver left knee. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Jeep Wrangler with code P0335?
No. Immediate shutdown / repair required to prevent permanent hardware destruction or total system lockup. Given that P0335 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.