P0125 on Jeep Gladiator
Factory diagnostic protocol and troubleshooting wire for fault code P0125 specifically for the Jeep Gladiator (2020–2026, 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave).
1. Symptoms of P0125 on Jeep Gladiator
When the Engine Control Module (ECM/PCM) on your Jeep Gladiator (3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave) logs fault code P0125, drivers commonly observe:
2. Most Likely Causes on Jeep Gladiator
Historical warranty claims and technical repair bulletins for Jeep Gladiator point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Jeep Gladiator
Check that engine coolant is at full mark and no external radiator or hose leaks exist. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Start cold engine and watch ECT climb. If it plateaus below 170°F (77°C) while driving, thermostat is stuck open. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Drain 1 gallon of coolant, remove thermostat housing bolts, install new OEM temperature-rated thermostat (typically 180°F–195°F) with jiggle valve at 12 o'clock. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Fill cooling system with 50/50 prediluted coolant, run engine with spill-free funnel to purge air bubbles. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Verify scan tool Fuel System Status changes from 'Open Loop' to 'Closed Loop' within 5 minutes. on the Jeep Gladiator equipped with 3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave.
Equipment for Diagnosing Jeep Gladiator (P0125)
OEM Thermostat & Gasket Assembly
Direct-replacement thermostat calibrated to factory operating temperature for Jeep Gladiator.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Jeep Gladiator
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Jeep Gladiator:
4. Jeep Gladiator P0125 FAQs
What causes code P0125 to trigger on a Jeep Gladiator?
On the Jeep Gladiator (3.6L Pentastar V6 (285HP) / 3.0L EcoDiesel V6 (260HP 442 lb-ft) / Mojave), P0125 is most frequently caused by Thermostat stuck open or opening prematurely or Low engine coolant level / air pocket around ECT sensor.
Where is the OBD-II port located on my Jeep Gladiator?
On the Jeep Gladiator, the 16-pin DLC diagnostic connector is located Under driver dash near left knee kick panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Jeep Gladiator with code P0125?
Yes, for short distances. Fuel economy will drop 15–25% as the engine remains trapped in open-loop enrichment. Given that P0125 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.