P0705 on Jeep Compass
Factory diagnostic protocol and troubleshooting wire for fault code P0705 specifically for the Jeep Compass (2021–2026, 2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP)).
1. Symptoms of P0705 on Jeep Compass
When the Engine Control Module (ECM/PCM) on your Jeep Compass (2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP)) logs fault code P0705, drivers commonly observe:
2. Most Likely Causes on Jeep Compass
Historical warranty claims and technical repair bulletins for Jeep Compass point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Jeep Compass
Move gear selector through all positions while monitoring scan tool TR PID to see which gear positions fail to register. on the Jeep Compass equipped with 2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP).
Ensure the mechanical shift linkage fully clicks the transmission lever into the physical detent for Park and Neutral. on the Jeep Compass equipped with 2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP).
Use multimeter to check continuity across switch pins in Park, Reverse, Neutral, and Drive. on the Jeep Compass equipped with 2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP).
Loosen mounting bolts, use alignment pin to align sensor slot with transmission shaft in Neutral, torque bolts, or install new OEM sensor. on the Jeep Compass equipped with 2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP).
Clear DTCs and confirm engine starts in Park and Neutral, reverse lights activate, and gear display is accurate. on the Jeep Compass equipped with 2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP).
Equipment for Diagnosing Jeep Compass (P0705)
Jeep Compass OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Jeep Compass.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Jeep Compass
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Jeep Compass:
4. Jeep Compass P0705 FAQs
What causes code P0705 to trigger on a Jeep Compass?
On the Jeep Compass (2.0L MultiAir Turbo 4-Cyl (177HP) / 1.3L Turbo 4xe PHEV (240HP)), P0705 is most frequently caused by Misaligned or faulty Transmission Range Sensor / Neutral Safety Switch (NSS) or Corroded or water-logged connector on transmission side.
Where is the OBD-II port located on my Jeep Compass?
On the Jeep Compass, the 16-pin DLC diagnostic connector is located Driver lower dash near hood lever assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Jeep Compass with code P0705?
Caution. Vehicle may not start in Park, backup lights may not work, and transmission may lock in Limp Mode. Given that P0705 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.