P2119 on Ford F-250 Super Duty: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P2119 (P2119: Throttle Actuator Control Throttle Body Range/Performance) specifically on the Ford F-250 Super Duty (2020–2026, 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8).
1. Symptoms of P2119 on Ford F-250 Super Duty
When the Engine Control Module (ECM/PCM) on your Ford F-250 Super Duty (6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8) logs fault code P2119, drivers commonly observe:
2. Most Likely Causes on Ford F-250 Super Duty
Historical warranty claims and technical repair bulletins for Ford F-250 Super Duty point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Ford F-250 Super Duty
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P2119 is static or intermittent. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Visually inspect the physical component (Throttle Plate Carbon Jamming), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Other Common Fault Codes on Ford F-250 Super Duty
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Ford F-250 Super Duty:
4. Ford F-250 Super Duty P2119 FAQs
What causes code P2119 to trigger on a Ford F-250 Super Duty?
On the Ford F-250 Super Duty (6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8), P2119 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Throttle Plate Carbon Jamming) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Ford F-250 Super Duty?
On the Ford F-250 Super Duty, the 16-pin DLC diagnostic connector is located Driver lower kick panel near emergency brake pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Ford F-250 Super Duty with code P2119?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P2119 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.