P2119 on Ford Bronco: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P2119 (P2119: Throttle Actuator Control Throttle Body Range/Performance) specifically on the Ford Bronco (2021–2026, 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)).
1. Symptoms of P2119 on Ford Bronco
When the Engine Control Module (ECM/PCM) on your Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)) logs fault code P2119, drivers commonly observe:
2. Most Likely Causes on Ford Bronco
Historical warranty claims and technical repair bulletins for Ford Bronco point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Ford Bronco
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P2119 is static or intermittent. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Visually inspect the physical component (Throttle Plate Carbon Jamming), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Other Common Fault Codes on Ford Bronco
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Ford Bronco:
4. Ford Bronco P2119 FAQs
What causes code P2119 to trigger on a Ford Bronco?
On the Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)), P2119 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Throttle Plate Carbon Jamming) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Ford Bronco?
On the Ford Bronco, the 16-pin DLC diagnostic connector is located Beneath steering wheel lower shroud. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Ford Bronco with code P2119?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P2119 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.