P0117 on Ford F-250 Super Duty
Factory diagnostic protocol and troubleshooting wire for fault code P0117 specifically for the Ford F-250 Super Duty (2020–2026, 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8).
1. Symptoms of P0117 on Ford F-250 Super Duty
When the Engine Control Module (ECM/PCM) on your Ford F-250 Super Duty (6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8) logs fault code P0117, drivers commonly observe:
2. Most Likely Causes on Ford F-250 Super Duty
Historical warranty claims and technical repair bulletins for Ford F-250 Super Duty point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Ford F-250 Super Duty
Read ECT live PID on scanner. If it reads 284°F (140°C) or higher with engine cold, a short to ground exists. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Unplug sensor connector while watching live data. If temperature drops to -40°F (-40°C), the sensor itself is shorted. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
If reading stays pegged at max with sensor unplugged, inspect harness for pinch points grounding against engine block. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Allow engine to cool, unscrew old ECT sensor from coolant crossover pipe or thermostat housing, install new OEM sensor with fresh thread sealant. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Bleed air from cooling system, clear DTCs, and verify normal temperature rise on live data. on the Ford F-250 Super Duty equipped with 6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8.
Equipment for Diagnosing Ford F-250 Super Duty (P0117)
VVT Oil Control Solenoid Valve
Restores accurate camshaft timing and oil pressure regulation on Ford F-250 Super Duty.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Ford F-250 Super Duty
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Ford F-250 Super Duty:
4. Ford F-250 Super Duty P0117 FAQs
What causes code P0117 to trigger on a Ford F-250 Super Duty?
On the Ford F-250 Super Duty (6.7L Power Stroke V8 Turbo Diesel (500HP / 1,200 lb-ft) / 7.3L Godzilla V8), P0117 is most frequently caused by ECT sensor internal short to ground or Short circuit to ground in ECT signal wiring harness.
Where is the OBD-II port located on my Ford F-250 Super Duty?
On the Ford F-250 Super Duty, the 16-pin DLC diagnostic connector is located Driver lower kick panel near emergency brake pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Ford F-250 Super Duty with code P0117?
No. The ECU thinks the engine is at 280°F+ (overheating) and runs rich or disables cooling fan logic. Given that P0117 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.