P2195 on Dodge Challenger
Factory diagnostic protocol and troubleshooting wire for fault code P2195 specifically for the Dodge Challenger (2020–2026, 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)).
1. Symptoms of P2195 on Dodge Challenger
When the Engine Control Module (ECM/PCM) on your Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)) logs fault code P2195, drivers commonly observe:
2. Most Likely Causes on Dodge Challenger
Historical warranty claims and technical repair bulletins for Dodge Challenger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Challenger
Check exhaust manifold near Bank 1 Sensor 1 for cracks or blown gaskets sucking in fresh air. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Check B1S1 AFR sensor output. On Toyota/Lexus, 3.3V is stoichiometric; a sensor stuck at 4.0V+ indicates lean bias. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Briefly spray unlit propane into intake. If sensor voltage does not quickly drop rich, the sensor element is poisoned. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Install a new genuine OEM Denso / Bosch upstream A/F sensor. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Clear DTCs, reset ECU learned trims, and road test. on the Dodge Challenger equipped with 3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP).
Equipment for Diagnosing Dodge Challenger (P2195)
Dodge Challenger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Challenger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Challenger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Challenger:
4. Dodge Challenger P2195 FAQs
What causes code P2195 to trigger on a Dodge Challenger?
On the Dodge Challenger (3.6L Pentastar V6 (305HP) / 5.7L HEMI V8 / 6.2L Redeye Widebody (807HP)), P2195 is most frequently caused by Contaminated or failing upstream Air-Fuel Ratio (AFR) / O2 sensor or Exhaust manifold crack or gasket leak before the sensor.
Where is the OBD-II port located on my Dodge Challenger?
On the Dodge Challenger, the 16-pin DLC diagnostic connector is located Under driver dash left of center stack. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Challenger with code P2195?
Caution. ECU may over-enrich fuel mixture trying to compensate for a falsely reported lean signal. Given that P2195 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.