P0705 on Acura Integra
Factory diagnostic protocol and troubleshooting wire for fault code P0705 specifically for the Acura Integra (2023–2026, 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP)).
1. Symptoms of P0705 on Acura Integra
When the Engine Control Module (ECM/PCM) on your Acura Integra (1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP)) logs fault code P0705, drivers commonly observe:
2. Most Likely Causes on Acura Integra
Historical warranty claims and technical repair bulletins for Acura Integra point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Acura Integra
Move gear selector through all positions while monitoring scan tool TR PID to see which gear positions fail to register. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Ensure the mechanical shift linkage fully clicks the transmission lever into the physical detent for Park and Neutral. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Use multimeter to check continuity across switch pins in Park, Reverse, Neutral, and Drive. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Loosen mounting bolts, use alignment pin to align sensor slot with transmission shaft in Neutral, torque bolts, or install new OEM sensor. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Clear DTCs and confirm engine starts in Park and Neutral, reverse lights activate, and gear display is accurate. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Equipment for Diagnosing Acura Integra (P0705)
Acura Integra OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Acura Integra.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Acura Integra
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Acura Integra:
4. Acura Integra P0705 FAQs
What causes code P0705 to trigger on a Acura Integra?
On the Acura Integra (1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP)), P0705 is most frequently caused by Misaligned or faulty Transmission Range Sensor / Neutral Safety Switch (NSS) or Corroded or water-logged connector on transmission side.
Where is the OBD-II port located on my Acura Integra?
On the Acura Integra, the 16-pin DLC diagnostic connector is located Under driver dash, right of steering column. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Acura Integra with code P0705?
Caution. Vehicle may not start in Park, backup lights may not work, and transmission may lock in Limp Mode. Given that P0705 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.