P0300 on Acura Integra: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0300 (P0300: Random or Multiple Cylinder Misfire Detected) specifically on the Acura Integra (2023–2026, 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP)).
1. Symptoms of P0300 on Acura Integra
When the Engine Control Module (ECM/PCM) on your Acura Integra (1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP)) logs fault code P0300, drivers commonly observe:
2. Most Likely Causes on Acura Integra
Historical warranty claims and technical repair bulletins for Acura Integra point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Acura Integra
Plug a handheld OBD-II scanner into the 16-pin port under the dashboard. Check if specific cylinder codes like P0301 (Cylinder 1) or P0304 (Cylinder 4) accompany P0300. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Remove the ignition coils, use a spark plug socket with ratchet to unthread spark plugs. Inspect electrode tips for carbon buildup, oil fouling, or burnt gaps. Replace with OEM iridium plugs gapped to spec. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Perform an ignition swap test: Swap coil from a suspected misfiring cylinder to an adjacent cylinder. Clear codes and re-scan. If the misfire moves, replace the faulty coil. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Inspect PCV hoses, intake boot, and vacuum lines for cracking or hissing sounds while engine idles. Smoke test the intake if necessary. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Add a bottle of premium fuel injector cleaner (e.g. Chevron Techron). Clear the OBD-II codes with your scanner and take the car on a 15-minute drive cycle to confirm readiness monitors reset. on the Acura Integra equipped with 1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP).
Other Common Fault Codes on Acura Integra
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Acura Integra:
4. Acura Integra P0300 FAQs
What causes code P0300 to trigger on a Acura Integra?
On the Acura Integra (1.5L VTEC Turbo (200HP) / 2.0L VTEC Turbo (Type S 320HP)), P0300 is most frequently caused by Worn or fouled spark plugs and damaged spark plug wires or Failing ignition coils or coil packs.
Where is the OBD-II port located on my Acura Integra?
On the Acura Integra, the 16-pin DLC diagnostic connector is located Under driver dash, right of steering column. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Acura Integra with code P0300?
No. Driving with a flashing check engine light causes irreversible catalytic converter damage. Given that P0300 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.