P0137 on Subaru Crosstrek
Factory diagnostic protocol and troubleshooting wire for fault code P0137 specifically for the Subaru Crosstrek (2021–2026, 2.0L Boxer-4 (152HP) / 2.5L (182HP) / 2.0L PHEV Plug-In Hybrid (149HP)).
1. Symptoms of P0137 on Subaru Crosstrek
When the Engine Control Module (ECM/PCM) on your Subaru Crosstrek (2.0L Boxer-4 (152HP) / 2.5L (182HP) / 2.0L PHEV Plug-In Hybrid (149HP)) logs fault code P0137, drivers commonly observe:
2. Most Likely Causes on Subaru Crosstrek
Historical warranty claims and technical repair bulletins for Subaru Crosstrek point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Subaru Crosstrek
Listen for exhaust ticking or black soot around flex pipe, flanges, and sensor bungs before the catalytic converter. on the Subaru Crosstrek equipped with 2.0L Boxer-4 (152HP) / 2.5L (182HP) / 2.0L PHEV Plug-In Hybrid (149HP).
Monitor B1S2 voltage. Snap the throttle to enrich mixture; voltage should briefly spike above 0.8V. If it remains 0.0V–0.1V, sensor is defective or shorted. on the Subaru Crosstrek equipped with 2.0L Boxer-4 (152HP) / 2.5L (182HP) / 2.0L PHEV Plug-In Hybrid (149HP).
Unplug harness, remove old sensor with 7/8 socket, install replacement sensor and plug firmly. on the Subaru Crosstrek equipped with 2.0L Boxer-4 (152HP) / 2.5L (182HP) / 2.0L PHEV Plug-In Hybrid (149HP).
Clear DTCs and verify B1S2 holds steady between 0.45V and 0.75V during steady highway cruising. on the Subaru Crosstrek equipped with 2.0L Boxer-4 (152HP) / 2.5L (182HP) / 2.0L PHEV Plug-In Hybrid (149HP).
Equipment for Diagnosing Subaru Crosstrek (P0137)
Subaru Crosstrek OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Subaru Crosstrek.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Subaru Crosstrek
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Subaru Crosstrek:
4. Subaru Crosstrek P0137 FAQs
What causes code P0137 to trigger on a Subaru Crosstrek?
On the Subaru Crosstrek (2.0L Boxer-4 (152HP) / 2.5L (182HP) / 2.0L PHEV Plug-In Hybrid (149HP)), P0137 is most frequently caused by Exhaust leak upstream of or directly at the Sensor 2 bung letting in fresh air or Faulty downstream oxygen sensor.
Where is the OBD-II port located on my Subaru Crosstrek?
On the Subaru Crosstrek, the 16-pin DLC diagnostic connector is located Under driver side steering column. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Subaru Crosstrek with code P0137?
Yes. Vehicle is fully drivable, but Check Engine Light will remain illuminated. Given that P0137 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.