P0705 on RAM 3500
Factory diagnostic protocol and troubleshooting wire for fault code P0705 specifically for the RAM 3500 (2020–2026, 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)).
1. Symptoms of P0705 on RAM 3500
When the Engine Control Module (ECM/PCM) on your RAM 3500 (6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)) logs fault code P0705, drivers commonly observe:
2. Most Likely Causes on RAM 3500
Historical warranty claims and technical repair bulletins for RAM 3500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 3500
Move gear selector through all positions while monitoring scan tool TR PID to see which gear positions fail to register. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Ensure the mechanical shift linkage fully clicks the transmission lever into the physical detent for Park and Neutral. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Use multimeter to check continuity across switch pins in Park, Reverse, Neutral, and Drive. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Loosen mounting bolts, use alignment pin to align sensor slot with transmission shaft in Neutral, torque bolts, or install new OEM sensor. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Clear DTCs and confirm engine starts in Park and Neutral, reverse lights activate, and gear display is accurate. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Equipment for Diagnosing RAM 3500 (P0705)
RAM 3500 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for RAM 3500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 3500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 3500:
4. RAM 3500 P0705 FAQs
What causes code P0705 to trigger on a RAM 3500?
On the RAM 3500 (6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)), P0705 is most frequently caused by Misaligned or faulty Transmission Range Sensor / Neutral Safety Switch (NSS) or Corroded or water-logged connector on transmission side.
Where is the OBD-II port located on my RAM 3500?
On the RAM 3500, the 16-pin DLC diagnostic connector is located Driver lower kick panel near emergency brake assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 3500 with code P0705?
Caution. Vehicle may not start in Park, backup lights may not work, and transmission may lock in Limp Mode. Given that P0705 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.