P0230 on RAM 3500
Factory diagnostic protocol and troubleshooting wire for fault code P0230 specifically for the RAM 3500 (2020–2026, 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)).
1. Symptoms of P0230 on RAM 3500
When the Engine Control Module (ECM/PCM) on your RAM 3500 (6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)) logs fault code P0230, drivers commonly observe:
2. Most Likely Causes on RAM 3500
Historical warranty claims and technical repair bulletins for RAM 3500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 3500
Inspect the Fuel Pump fuse in under-hood fuse box. Swap the fuel pump relay with an identical non-critical relay (like the horn relay). on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Have an assistant turn key to ON while listening at the open fuel filler neck. A healthy pump hums for 2–3 seconds. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Check for 12V battery power on pin 30 and 86, and check for PCM ground command on pin 85 when key is turned on. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
On vehicles with an electronic FPDM (such as Ford F-150s mounted on rear axle), check for corrosion or cracked aluminum housing. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
If power and ground reach the pump connector but pump does not spin, drop tank or access fuel pump hatch to replace pump assembly. on the RAM 3500 equipped with 6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel).
Equipment for Diagnosing RAM 3500 (P0230)
RAM 3500 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for RAM 3500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 3500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 3500:
4. RAM 3500 P0230 FAQs
What causes code P0230 to trigger on a RAM 3500?
On the RAM 3500 (6.7L High-Output Cummins Turbo-Diesel (420HP / 1,075 lb-ft torque / Dual Rear Wheel)), P0230 is most frequently caused by Blown fuel pump fuse or burnt fuel pump relay or Open or shorted control circuit wiring between PCM and fuel pump relay.
Where is the OBD-II port located on my RAM 3500?
On the RAM 3500, the 16-pin DLC diagnostic connector is located Driver lower kick panel near emergency brake assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 3500 with code P0230?
No. The engine will crank but not start or will suddenly stall while driving when the fuel pump cuts out. Given that P0230 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.