U0142 on RAM 2500
Factory diagnostic protocol and troubleshooting wire for fault code U0142 specifically for the RAM 2500 (2020–2026, 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)).
1. Symptoms of U0142 on RAM 2500
When the Engine Control Module (ECM/PCM) on your RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)) logs fault code U0142, drivers commonly observe:
2. Most Likely Causes on RAM 2500
Historical warranty claims and technical repair bulletins for RAM 2500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 2500
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code U0142 to note engine RPM, load, and voltage when the fault triggered. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Inspect the electrical connector and wiring harness related to U0142 for chafing, corrosion, moisture, or pin push-out. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Equipment for Diagnosing RAM 2500 (U0142)
RAM 2500 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for RAM 2500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 2500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 2500:
4. RAM 2500 U0142 FAQs
What causes code U0142 to trigger on a RAM 2500?
On the RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)), U0142 is most frequently caused by CAN bus communication break or Blown BCM fuse.
Where is the OBD-II port located on my RAM 2500?
On the RAM 2500, the 16-pin DLC diagnostic connector is located Driver footwell below steering column near parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 2500 with code U0142?
Yes. Secondary body electronics offline. Given that U0142 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.