P0150 on RAM 2500
Factory diagnostic protocol and troubleshooting wire for fault code P0150 specifically for the RAM 2500 (2020–2026, 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)).
1. Symptoms of P0150 on RAM 2500
When the Engine Control Module (ECM/PCM) on your RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)) logs fault code P0150, drivers commonly observe:
2. Most Likely Causes on RAM 2500
Historical warranty claims and technical repair bulletins for RAM 2500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 2500
Identify Bank 2 (the cylinder bank that does NOT contain Cylinder 1). Locate the upstream O2 sensor before the catalytic converter. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Check the 4-wire or 5-wire harness for damage. Measure heater resistance across pins (typically 4–15 ohms). on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Use an O2 sensor socket to remove the old sensor, thread in new OEM replacement, and torque securely. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Clear DTCs and monitor Bank 2 Short Term Fuel Trim (STFT) to verify fuel control restoration. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Equipment for Diagnosing RAM 2500 (P0150)
RAM 2500 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for RAM 2500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 2500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 2500:
4. RAM 2500 P0150 FAQs
What causes code P0150 to trigger on a RAM 2500?
On the RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)), P0150 is most frequently caused by Failing Bank 2 upstream oxygen sensor or Damaged wiring or melted harness on Bank 2 exhaust manifold.
Where is the OBD-II port located on my RAM 2500?
On the RAM 2500, the 16-pin DLC diagnostic connector is located Driver footwell below steering column near parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 2500 with code P0150?
Yes, for limited driving. Bank 2 cylinders will operate in open-loop fail-safe mode. Given that P0150 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.