P0116 on RAM 2500
Factory diagnostic protocol and troubleshooting wire for fault code P0116 specifically for the RAM 2500 (2020–2026, 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)).
1. Symptoms of P0116 on RAM 2500
When the Engine Control Module (ECM/PCM) on your RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)) logs fault code P0116, drivers commonly observe:
2. Most Likely Causes on RAM 2500
Historical warranty claims and technical repair bulletins for RAM 2500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 2500
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P0116 to note engine RPM, load, and voltage when the fault triggered. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Inspect the electrical connector and wiring harness related to P0116 for chafing, corrosion, moisture, or pin push-out. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the RAM 2500 equipped with 6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP).
Equipment for Diagnosing RAM 2500 (P0116)
VVT Oil Control Solenoid Valve
Restores accurate camshaft timing and oil pressure regulation on RAM 2500.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on RAM 2500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 2500:
4. RAM 2500 P0116 FAQs
What causes code P0116 to trigger on a RAM 2500?
On the RAM 2500 (6.7L Cummins Turbo-Diesel I6 (420HP / 1,075 lb-ft) / 6.4L HEMI V8 (410HP)), P0116 is most frequently caused by Stuck open thermostat or Air pocket in cooling system.
Where is the OBD-II port located on my RAM 2500?
On the RAM 2500, the 16-pin DLC diagnostic connector is located Driver footwell below steering column near parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 2500 with code P0116?
Caution. Verify engine is not overheating. Given that P0116 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.