P0122 on RAM 1500: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0122 (P0122: Throttle Position Sensor (TPS) Circuit Low Input) specifically on the RAM 1500 (2020–2026, 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar).
1. Symptoms of P0122 on RAM 1500
When the Engine Control Module (ECM/PCM) on your RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar) logs fault code P0122, drivers commonly observe:
2. Most Likely Causes on RAM 1500
Historical warranty claims and technical repair bulletins for RAM 1500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 1500
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0122 is static or intermittent. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Visually inspect the physical component (TPS Potentiometer), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Other Common Fault Codes on RAM 1500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 1500:
4. RAM 1500 P0122 FAQs
What causes code P0122 to trigger on a RAM 1500?
On the RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar), P0122 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (TPS Potentiometer) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my RAM 1500?
On the RAM 1500, the 16-pin DLC diagnostic connector is located Driver lower knee bolster panel to the right of parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 1500 with code P0122?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P0122 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.