P0024 on RAM 1500: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0024 (P0024: Exhaust Camshaft Position Timing Over-Advanced (Bank 2)) specifically on the RAM 1500 (2020–2026, 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar).
1. Symptoms of P0024 on RAM 1500
When the Engine Control Module (ECM/PCM) on your RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar) logs fault code P0024, drivers commonly observe:
2. Most Likely Causes on RAM 1500
Historical warranty claims and technical repair bulletins for RAM 1500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for RAM 1500
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0024 is static or intermittent. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Visually inspect the physical component (Bank 2 Exhaust Cam Phaser), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the RAM 1500 equipped with 3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar.
Other Common Fault Codes on RAM 1500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the RAM 1500:
4. RAM 1500 P0024 FAQs
What causes code P0024 to trigger on a RAM 1500?
On the RAM 1500 (3.0L Hurricane Twin-Turbo I6 (420HP/540HP) / 5.7L HEMI V8 eTorque / 3.6L Pentastar), P0024 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Bank 2 Exhaust Cam Phaser) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my RAM 1500?
On the RAM 1500, the 16-pin DLC diagnostic connector is located Driver lower knee bolster panel to the right of parking brake. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my RAM 1500 with code P0024?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P0024 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.