P0238 on Mercedes-Benz S-Class: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0238 (P0238: Turbocharger Boost Sensor A Circuit High Input) specifically on the Mercedes-Benz S-Class (2021–2026, 3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP)).
1. Symptoms of P0238 on Mercedes-Benz S-Class
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz S-Class (3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP)) logs fault code P0238, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz S-Class
Historical warranty claims and technical repair bulletins for Mercedes-Benz S-Class point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz S-Class
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0238 is static or intermittent. on the Mercedes-Benz S-Class equipped with 3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP).
Visually inspect the physical component (Boost Sensor Open Circuit), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Mercedes-Benz S-Class equipped with 3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Mercedes-Benz S-Class equipped with 3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Mercedes-Benz S-Class equipped with 3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Mercedes-Benz S-Class equipped with 3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP).
Other Common Fault Codes on Mercedes-Benz S-Class
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz S-Class:
4. Mercedes-Benz S-Class P0238 FAQs
What causes code P0238 to trigger on a Mercedes-Benz S-Class?
On the Mercedes-Benz S-Class (3.0L Turbo I6 (S 500) / 4.0L Bi-Turbo V8 (M176 S 580 496HP)), P0238 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Boost Sensor Open Circuit) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Mercedes-Benz S-Class?
On the Mercedes-Benz S-Class, the 16-pin DLC diagnostic connector is located Driver lower dash panel beneath protective hinged flap. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz S-Class with code P0238?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P0238 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.