C0244 on Mercedes-Benz GLS: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code C0244 (C0244: Pulse Width Modulated (PWM) Traction Control Error) specifically on the Mercedes-Benz GLS (2020–2026, 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)).
1. Symptoms of C0244 on Mercedes-Benz GLS
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLS (3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)) logs fault code C0244, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLS
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLS point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLS
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether C0244 is static or intermittent. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Visually inspect the physical component (Electronic Brake Control Module (EBCM)), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Mercedes-Benz GLS equipped with 3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach).
Other Common Fault Codes on Mercedes-Benz GLS
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLS:
4. Mercedes-Benz GLS C0244 FAQs
What causes code C0244 to trigger on a Mercedes-Benz GLS?
On the Mercedes-Benz GLS (3.0L Turbo I6 (GLS 450) / 4.0L Bi-Turbo V8 (GLS 580 / Maybach)), C0244 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Electronic Brake Control Module (EBCM)) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Mercedes-Benz GLS?
On the Mercedes-Benz GLS, the 16-pin DLC diagnostic connector is located Driver lower knee bolster trim panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLS with code C0244?
Yes, for temporary operations. However, resolve promptly to maintain optimal efficiency and prevent cascade failures. Given that C0244 carries a Moderate severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.