C0045 on Mercedes-Benz GLE: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code C0045 (C0045: Left Rear Wheel Speed Sensor Circuit Malfunction) specifically on the Mercedes-Benz GLE (2020–2026, 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580).
1. Symptoms of C0045 on Mercedes-Benz GLE
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580) logs fault code C0045, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz GLE
Historical warranty claims and technical repair bulletins for Mercedes-Benz GLE point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz GLE
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether C0045 is static or intermittent. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Visually inspect the physical component (Rear Left ABS Speed Sensor), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Mercedes-Benz GLE equipped with 2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580.
Other Common Fault Codes on Mercedes-Benz GLE
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz GLE:
4. Mercedes-Benz GLE C0045 FAQs
What causes code C0045 to trigger on a Mercedes-Benz GLE?
On the Mercedes-Benz GLE (2.0L Turbo / 3.0L Turbo I6 (GLE 450 375HP) / 4.0L V8 GLE 580), C0045 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Rear Left ABS Speed Sensor) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Mercedes-Benz GLE?
On the Mercedes-Benz GLE, the 16-pin DLC diagnostic connector is located Driver footwell directly above parking brake pedal. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz GLE with code C0045?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that C0045 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.