P0122 on Mercedes-Benz E-Class: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0122 (P0122: Throttle Position Sensor (TPS) Circuit Low Input) specifically on the Mercedes-Benz E-Class (2020–2026, 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP)).
1. Symptoms of P0122 on Mercedes-Benz E-Class
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz E-Class (2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP)) logs fault code P0122, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz E-Class
Historical warranty claims and technical repair bulletins for Mercedes-Benz E-Class point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz E-Class
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0122 is static or intermittent. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Visually inspect the physical component (TPS Potentiometer), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Mercedes-Benz E-Class equipped with 2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP).
Other Common Fault Codes on Mercedes-Benz E-Class
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz E-Class:
4. Mercedes-Benz E-Class P0122 FAQs
What causes code P0122 to trigger on a Mercedes-Benz E-Class?
On the Mercedes-Benz E-Class (2.0L Turbo 4-Cyl (E 350) / 3.0L Turbo Inline-6 (M256 E 450 375HP)), P0122 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (TPS Potentiometer) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Mercedes-Benz E-Class?
On the Mercedes-Benz E-Class, the 16-pin DLC diagnostic connector is located Under driver dashboard behind safety clip bezel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz E-Class with code P0122?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P0122 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.