P0760 on Mercedes-Benz C-Class: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0760 (P0760: Shift Solenoid C Malfunction) specifically on the Mercedes-Benz C-Class (2020–2026, 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)).
1. Symptoms of P0760 on Mercedes-Benz C-Class
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz C-Class (2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)) logs fault code P0760, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz C-Class
Historical warranty claims and technical repair bulletins for Mercedes-Benz C-Class point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz C-Class
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0760 is static or intermittent. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Visually inspect the physical component (Shift Solenoid C), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Other Common Fault Codes on Mercedes-Benz C-Class
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz C-Class:
4. Mercedes-Benz C-Class P0760 FAQs
What causes code P0760 to trigger on a Mercedes-Benz C-Class?
On the Mercedes-Benz C-Class (2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)), P0760 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Shift Solenoid C) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Mercedes-Benz C-Class?
On the Mercedes-Benz C-Class, the 16-pin DLC diagnostic connector is located Under driver dash beneath purple/black sliding protective door. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz C-Class with code P0760?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P0760 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.