P0672 on Mercedes-Benz C-Class: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0672 (P0672: Cylinder 2 Glow Plug Circuit Malfunction) specifically on the Mercedes-Benz C-Class (2020–2026, 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)).
1. Symptoms of P0672 on Mercedes-Benz C-Class
When the Engine Control Module (ECM/PCM) on your Mercedes-Benz C-Class (2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)) logs fault code P0672, drivers commonly observe:
2. Most Likely Causes on Mercedes-Benz C-Class
Historical warranty claims and technical repair bulletins for Mercedes-Benz C-Class point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Mercedes-Benz C-Class
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0672 is static or intermittent. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Visually inspect the physical component (Cylinder 2 Glow Plug), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Mercedes-Benz C-Class equipped with 2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP).
Other Common Fault Codes on Mercedes-Benz C-Class
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Mercedes-Benz C-Class:
4. Mercedes-Benz C-Class P0672 FAQs
What causes code P0672 to trigger on a Mercedes-Benz C-Class?
On the Mercedes-Benz C-Class (2.0L Turbo 4-Cyl with 48V Mild Hybrid (M254 255HP) / AMG C 43 (402HP)), P0672 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Cylinder 2 Glow Plug) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Mercedes-Benz C-Class?
On the Mercedes-Benz C-Class, the 16-pin DLC diagnostic connector is located Under driver dash beneath purple/black sliding protective door. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Mercedes-Benz C-Class with code P0672?
Yes, for temporary operations. However, resolve promptly to maintain optimal efficiency and prevent cascade failures. Given that P0672 carries a Moderate severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.