B1325 on Hyundai Sonata: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code B1325 (B1325: Device Power 1 Circuit Voltage Below Threshold (BCM)) specifically on the Hyundai Sonata (2020–2026, 2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP)).
1. Symptoms of B1325 on Hyundai Sonata
When the Engine Control Module (ECM/PCM) on your Hyundai Sonata (2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP)) logs fault code B1325, drivers commonly observe:
2. Most Likely Causes on Hyundai Sonata
Historical warranty claims and technical repair bulletins for Hyundai Sonata point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Hyundai Sonata
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether B1325 is static or intermittent. on the Hyundai Sonata equipped with 2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP).
Visually inspect the physical component (Main BCM Ground Wire), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Hyundai Sonata equipped with 2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Hyundai Sonata equipped with 2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Hyundai Sonata equipped with 2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Hyundai Sonata equipped with 2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP).
Other Common Fault Codes on Hyundai Sonata
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Hyundai Sonata:
4. Hyundai Sonata B1325 FAQs
What causes code B1325 to trigger on a Hyundai Sonata?
On the Hyundai Sonata (2.5L 4-Cyl (191HP) / 2.5L Turbo (N Line 290HP) / 2.0L Hybrid (192HP)), B1325 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Main BCM Ground Wire) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Hyundai Sonata?
On the Hyundai Sonata, the 16-pin DLC diagnostic connector is located Under driver side steering column. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Hyundai Sonata with code B1325?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that B1325 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.