P0122 on Hyundai Ioniq 5: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0122 (P0122: Throttle Position Sensor (TPS) Circuit Low Input) specifically on the Hyundai Ioniq 5 (2022–2026, Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP)).
1. Symptoms of P0122 on Hyundai Ioniq 5
When the Engine Control Module (ECM/PCM) on your Hyundai Ioniq 5 (Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP)) logs fault code P0122, drivers commonly observe:
2. Most Likely Causes on Hyundai Ioniq 5
Historical warranty claims and technical repair bulletins for Hyundai Ioniq 5 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Hyundai Ioniq 5
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0122 is static or intermittent. on the Hyundai Ioniq 5 equipped with Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP).
Visually inspect the physical component (TPS Potentiometer), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Hyundai Ioniq 5 equipped with Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Hyundai Ioniq 5 equipped with Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Hyundai Ioniq 5 equipped with Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Hyundai Ioniq 5 equipped with Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP).
Other Common Fault Codes on Hyundai Ioniq 5
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Hyundai Ioniq 5:
4. Hyundai Ioniq 5 P0122 FAQs
What causes code P0122 to trigger on a Hyundai Ioniq 5?
On the Hyundai Ioniq 5 (Dual Motor AWD (320HP) / Single Motor RWD (225HP) / Ioniq 5 N (641HP)), P0122 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (TPS Potentiometer) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Hyundai Ioniq 5?
On the Hyundai Ioniq 5, the 16-pin DLC diagnostic connector is located Driver side lower dash bezel near steering base. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Hyundai Ioniq 5 with code P0122?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that P0122 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.