B1325 on GMC Sierra 1500: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code B1325 (B1325: Device Power 1 Circuit Voltage Below Threshold (BCM)) specifically on the GMC Sierra 1500 (2020–2026, 5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel).
1. Symptoms of B1325 on GMC Sierra 1500
When the Engine Control Module (ECM/PCM) on your GMC Sierra 1500 (5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel) logs fault code B1325, drivers commonly observe:
2. Most Likely Causes on GMC Sierra 1500
Historical warranty claims and technical repair bulletins for GMC Sierra 1500 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for GMC Sierra 1500
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether B1325 is static or intermittent. on the GMC Sierra 1500 equipped with 5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel.
Visually inspect the physical component (Main BCM Ground Wire), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the GMC Sierra 1500 equipped with 5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel.
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the GMC Sierra 1500 equipped with 5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel.
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the GMC Sierra 1500 equipped with 5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel.
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the GMC Sierra 1500 equipped with 5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel.
Other Common Fault Codes on GMC Sierra 1500
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the GMC Sierra 1500:
4. GMC Sierra 1500 B1325 FAQs
What causes code B1325 to trigger on a GMC Sierra 1500?
On the GMC Sierra 1500 (5.3L / 6.2L EcoTec3 V8 (Denali 420HP) / 3.0L Duramax Turbo-Diesel), B1325 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Main BCM Ground Wire) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my GMC Sierra 1500?
On the GMC Sierra 1500, the 16-pin DLC diagnostic connector is located Under driver dashboard, left of steering column. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my GMC Sierra 1500 with code B1325?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that B1325 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.