U0073 on Ford Bronco
Factory diagnostic protocol and troubleshooting wire for fault code U0073 specifically for the Ford Bronco (2021–2026, 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)).
1. Symptoms of U0073 on Ford Bronco
When the Engine Control Module (ECM/PCM) on your Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)) logs fault code U0073, drivers commonly observe:
2. Most Likely Causes on Ford Bronco
Historical warranty claims and technical repair bulletins for Ford Bronco point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Ford Bronco
Remove any aftermarket insurance dongles, GPS trackers, or scan tools plugged into the DLC port. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Inspect braided ground straps on engine and transmission. Clean all contact surfaces to bare metal. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Scan all modules on vehicle. Note which modules are online and which are offline to pinpoint the break in the network daisy-chain. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Verify 60 ohms across Pins 6 and 14 with battery disconnected. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Clear DTCs from all modules and road test to verify error-free network transmission. on the Ford Bronco equipped with 2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP).
Equipment for Diagnosing Ford Bronco (U0073)
Ford Bronco OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Ford Bronco.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Ford Bronco
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Ford Bronco:
4. Ford Bronco U0073 FAQs
What causes code U0073 to trigger on a Ford Bronco?
On the Ford Bronco (2.3L EcoBoost (300HP) / 2.7L Twin-Turbo V6 (330HP) / 3.0L Raptor (418HP)), U0073 is most frequently caused by Loose or corroded ground connection on transmission or frame or Faulty Transmission Control Module (TCM) or ABS module pulling bus down.
Where is the OBD-II port located on my Ford Bronco?
On the Ford Bronco, the 16-pin DLC diagnostic connector is located Beneath steering wheel lower shroud. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Ford Bronco with code U0073?
No. Bus is shut down due to excessive transmission errors, leaving vehicle in unpredictable limp mode. Given that U0073 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.