P0705 on Dodge Durango
Factory diagnostic protocol and troubleshooting wire for fault code P0705 specifically for the Dodge Durango (2021–2026, 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP)).
1. Symptoms of P0705 on Dodge Durango
When the Engine Control Module (ECM/PCM) on your Dodge Durango (3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP)) logs fault code P0705, drivers commonly observe:
2. Most Likely Causes on Dodge Durango
Historical warranty claims and technical repair bulletins for Dodge Durango point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Durango
Move gear selector through all positions while monitoring scan tool TR PID to see which gear positions fail to register. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Ensure the mechanical shift linkage fully clicks the transmission lever into the physical detent for Park and Neutral. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Use multimeter to check continuity across switch pins in Park, Reverse, Neutral, and Drive. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Loosen mounting bolts, use alignment pin to align sensor slot with transmission shaft in Neutral, torque bolts, or install new OEM sensor. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Clear DTCs and confirm engine starts in Park and Neutral, reverse lights activate, and gear display is accurate. on the Dodge Durango equipped with 3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP).
Equipment for Diagnosing Dodge Durango (P0705)
Dodge Durango OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Durango.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Durango
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Durango:
4. Dodge Durango P0705 FAQs
What causes code P0705 to trigger on a Dodge Durango?
On the Dodge Durango (3.6L Pentastar V6 (293HP) / 5.7L HEMI V8 (360HP) / 6.4L 392 SRT (475HP)), P0705 is most frequently caused by Misaligned or faulty Transmission Range Sensor / Neutral Safety Switch (NSS) or Corroded or water-logged connector on transmission side.
Where is the OBD-II port located on my Dodge Durango?
On the Dodge Durango, the 16-pin DLC diagnostic connector is located Driver lower dash panel near fuse box. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Durango with code P0705?
Caution. Vehicle may not start in Park, backup lights may not work, and transmission may lock in Limp Mode. Given that P0705 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.