P0341 on Dodge Charger
Factory diagnostic protocol and troubleshooting wire for fault code P0341 specifically for the Dodge Charger (2020–2026, 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo).
1. Symptoms of P0341 on Dodge Charger
When the Engine Control Module (ECM/PCM) on your Dodge Charger (5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo) logs fault code P0341, drivers commonly observe:
2. Most Likely Causes on Dodge Charger
Historical warranty claims and technical repair bulletins for Dodge Charger point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Dodge Charger
VVT systems require correct oil pressure. Check oil level on dipstick; if dirty or low, change oil and filter with OEM-grade synthetic. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Check actual vs desired camshaft phase angle on scan tool. If cam angle lags significantly behind target, timing chain stretch or VVT phaser failure is indicated. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Remove VVT solenoid, inspect screen for metal debris or sludge, and test 12V actuation with bench power. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Check 5V reference, ground, and 5V square-wave signal with lab scope or multimeter. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
If sensor and VVT solenoid test good, remove valve cover to inspect timing chain slack and alignment marks. on the Dodge Charger equipped with 5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo.
Equipment for Diagnosing Dodge Charger (P0341)
Dodge Charger OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Dodge Charger.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Dodge Charger
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Dodge Charger:
4. Dodge Charger P0341 FAQs
What causes code P0341 to trigger on a Dodge Charger?
On the Dodge Charger (5.7L / 6.4L 392 HEMI / 6.2L Hellcat (717HP–797HP) / Hurricane 3.0L Turbo), P0341 is most frequently caused by Stretched timing chain or worn timing belt jumped one tooth or Failed Variable Valve Timing (VVT) actuator phaser or oil control valve (OCV).
Where is the OBD-II port located on my Dodge Charger?
On the Dodge Charger, the 16-pin DLC diagnostic connector is located Driver lower dash assembly next to hood lever. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Dodge Charger with code P0341?
No. Stretched timing chain or incorrect camshaft timing can cause catastrophic valve-to-piston contact. Given that P0341 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.