P0230 on Chrysler Voyager
Factory diagnostic protocol and troubleshooting wire for fault code P0230 specifically for the Chrysler Voyager (2020–2026, 3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic)).
1. Symptoms of P0230 on Chrysler Voyager
When the Engine Control Module (ECM/PCM) on your Chrysler Voyager (3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic)) logs fault code P0230, drivers commonly observe:
2. Most Likely Causes on Chrysler Voyager
Historical warranty claims and technical repair bulletins for Chrysler Voyager point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chrysler Voyager
Inspect the Fuel Pump fuse in under-hood fuse box. Swap the fuel pump relay with an identical non-critical relay (like the horn relay). on the Chrysler Voyager equipped with 3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic).
Have an assistant turn key to ON while listening at the open fuel filler neck. A healthy pump hums for 2–3 seconds. on the Chrysler Voyager equipped with 3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic).
Check for 12V battery power on pin 30 and 86, and check for PCM ground command on pin 85 when key is turned on. on the Chrysler Voyager equipped with 3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic).
On vehicles with an electronic FPDM (such as Ford F-150s mounted on rear axle), check for corrosion or cracked aluminum housing. on the Chrysler Voyager equipped with 3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic).
If power and ground reach the pump connector but pump does not spin, drop tank or access fuel pump hatch to replace pump assembly. on the Chrysler Voyager equipped with 3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic).
Equipment for Diagnosing Chrysler Voyager (P0230)
Chrysler Voyager OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Chrysler Voyager.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Chrysler Voyager
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chrysler Voyager:
4. Chrysler Voyager P0230 FAQs
What causes code P0230 to trigger on a Chrysler Voyager?
On the Chrysler Voyager (3.6L Pentastar V6 24V VVT (287HP / 9-Speed Automatic)), P0230 is most frequently caused by Blown fuel pump fuse or burnt fuel pump relay or Open or shorted control circuit wiring between PCM and fuel pump relay.
Where is the OBD-II port located on my Chrysler Voyager?
On the Chrysler Voyager, the 16-pin DLC diagnostic connector is located Driver lower kick panel near hood release lever. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chrysler Voyager with code P0230?
No. The engine will crank but not start or will suddenly stall while driving when the fuel pump cuts out. Given that P0230 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.