B1325 on Chevrolet Corvette: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code B1325 (B1325: Device Power 1 Circuit Voltage Below Threshold (BCM)) specifically on the Chevrolet Corvette (2020–2026, 6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid).
1. Symptoms of B1325 on Chevrolet Corvette
When the Engine Control Module (ECM/PCM) on your Chevrolet Corvette (6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid) logs fault code B1325, drivers commonly observe:
2. Most Likely Causes on Chevrolet Corvette
Historical warranty claims and technical repair bulletins for Chevrolet Corvette point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Chevrolet Corvette
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether B1325 is static or intermittent. on the Chevrolet Corvette equipped with 6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid.
Visually inspect the physical component (Main BCM Ground Wire), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Chevrolet Corvette equipped with 6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid.
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Chevrolet Corvette equipped with 6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid.
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Chevrolet Corvette equipped with 6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid.
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Chevrolet Corvette equipped with 6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid.
Other Common Fault Codes on Chevrolet Corvette
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Chevrolet Corvette:
4. Chevrolet Corvette B1325 FAQs
What causes code B1325 to trigger on a Chevrolet Corvette?
On the Chevrolet Corvette (6.2L LT2 Small Block V8 (495HP) / 5.5L Flat-Plane Z06 (670HP) / E-Ray Hybrid), B1325 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Main BCM Ground Wire) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Chevrolet Corvette?
On the Chevrolet Corvette, the 16-pin DLC diagnostic connector is located Driver footwell lower panel. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Chevrolet Corvette with code B1325?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that B1325 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.