P0304 on Audi Q5: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code P0304 (P0304: Cylinder 4 Misfire Detected) specifically on the Audi Q5 (2020–2026, 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV).
1. Symptoms of P0304 on Audi Q5
When the Engine Control Module (ECM/PCM) on your Audi Q5 (2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV) logs fault code P0304, drivers commonly observe:
2. Most Likely Causes on Audi Q5
Historical warranty claims and technical repair bulletins for Audi Q5 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Audi Q5
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether P0304 is static or intermittent. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Visually inspect the physical component (Cylinder 4 Spark Plug / Wiring), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Other Common Fault Codes on Audi Q5
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Audi Q5:
4. Audi Q5 P0304 FAQs
What causes code P0304 to trigger on a Audi Q5?
On the Audi Q5 (2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV), P0304 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Cylinder 4 Spark Plug / Wiring) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Audi Q5?
On the Audi Q5, the 16-pin DLC diagnostic connector is located Left side under driver steering column. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Audi Q5 with code P0304?
No. Immediate shutdown / repair required to prevent permanent hardware destruction or total system lockup. Given that P0304 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.