P0137 on Audi Q5
Factory diagnostic protocol and troubleshooting wire for fault code P0137 specifically for the Audi Q5 (2020–2026, 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV).
1. Symptoms of P0137 on Audi Q5
When the Engine Control Module (ECM/PCM) on your Audi Q5 (2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV) logs fault code P0137, drivers commonly observe:
2. Most Likely Causes on Audi Q5
Historical warranty claims and technical repair bulletins for Audi Q5 point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Audi Q5
Listen for exhaust ticking or black soot around flex pipe, flanges, and sensor bungs before the catalytic converter. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Monitor B1S2 voltage. Snap the throttle to enrich mixture; voltage should briefly spike above 0.8V. If it remains 0.0V–0.1V, sensor is defective or shorted. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Unplug harness, remove old sensor with 7/8 socket, install replacement sensor and plug firmly. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Clear DTCs and verify B1S2 holds steady between 0.45V and 0.75V during steady highway cruising. on the Audi Q5 equipped with 2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV.
Equipment for Diagnosing Audi Q5 (P0137)
Audi Q5 OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Audi Q5.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Audi Q5
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Audi Q5:
4. Audi Q5 P0137 FAQs
What causes code P0137 to trigger on a Audi Q5?
On the Audi Q5 (2.0L TFSI Turbo / 3.0L Turbo V6 (SQ5 349HP) / 55 TFSI e PHEV), P0137 is most frequently caused by Exhaust leak upstream of or directly at the Sensor 2 bung letting in fresh air or Faulty downstream oxygen sensor.
Where is the OBD-II port located on my Audi Q5?
On the Audi Q5, the 16-pin DLC diagnostic connector is located Left side under driver steering column. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Audi Q5 with code P0137?
Yes. Vehicle is fully drivable, but Check Engine Light will remain illuminated. Given that P0137 carries a Low severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.