P0744 on Acura MDX
Factory diagnostic protocol and troubleshooting wire for fault code P0744 specifically for the Acura MDX (2022–2026, 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)).
1. Symptoms of P0744 on Acura MDX
When the Engine Control Module (ECM/PCM) on your Acura MDX (3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)) logs fault code P0744, drivers commonly observe:
2. Most Likely Causes on Acura MDX
Historical warranty claims and technical repair bulletins for Acura MDX point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Acura MDX
Connect an OBD-II scan tool and record freeze frame sensor telemetry for code P0744 to note engine RPM, load, and voltage when the fault triggered. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Inspect the electrical connector and wiring harness related to P0744 for chafing, corrosion, moisture, or pin push-out. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Measure circuit voltage supply (12V B+ or 5V reference) and sensor/actuator resistance according to factory repair manual specifications. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Install a new OEM-grade replacement part, torque fasteners to factory spec, and ensure electrical locking tabs click firmly. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Clear all stored DTCs from vehicle memory and perform an OBD-II drive cycle to confirm the diagnostic monitor resets to 'Ready'. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Equipment for Diagnosing Acura MDX (P0744)
Acura MDX OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Acura MDX.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Acura MDX
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Acura MDX:
4. Acura MDX P0744 FAQs
What causes code P0744 to trigger on a Acura MDX?
On the Acura MDX (3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)), P0744 is most frequently caused by Intermittent TCC solenoid failure or Contaminated transmission fluid.
Where is the OBD-II port located on my Acura MDX?
On the Acura MDX, the 16-pin DLC diagnostic connector is located Driver side lower dash assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Acura MDX with code P0744?
Yes. Intermittent lockup slippage. Given that P0744 carries a Medium severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.