P0201 on Acura MDX
Factory diagnostic protocol and troubleshooting wire for fault code P0201 specifically for the Acura MDX (2022–2026, 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)).
1. Symptoms of P0201 on Acura MDX
When the Engine Control Module (ECM/PCM) on your Acura MDX (3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)) logs fault code P0201, drivers commonly observe:
2. Most Likely Causes on Acura MDX
Historical warranty claims and technical repair bulletins for Acura MDX point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Acura MDX
Locate Cylinder 1 fuel injector. Ensure connector is securely clicked in and wires are not frayed. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Unplug connector and measure resistance across the two injector pins. Normal is 11–16 ohms for high-impedance injectors. If open (OL) or shorted (0 ohms), replace injector. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Plug a noid light into the harness connector and crank engine. Rapid flashing confirms PCM driver is pulsing the circuit. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Relieve fuel rail pressure, unbolt fuel rail mounting bolts, gently pull rail up, remove retaining clip, and replace Cylinder 1 injector with new OEM unit with lubricated O-rings. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Turn key to ON to prime fuel system, check for fuel rail leaks, start engine, clear DTCs, and verify smooth idle. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Equipment for Diagnosing Acura MDX (P0201)
Acura MDX OEM Replacement Sensor
Direct-fit replacement assembly engineered to OEM tolerances for Acura MDX.
AstroAI Auto-Ranging Digital Multimeter
Essential for testing 0.1V–5.0V sensor reference signals, ground continuity (<0.20Ω), and harness resistance.
BlueDriver Bluetooth Pro OBDII Scan Tool
Reads and clears enhanced codes (ABS, Airbag, Transmission, Engine) & live freeze-frame telemetry on phone.
Other Common Fault Codes on Acura MDX
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Acura MDX:
4. Acura MDX P0201 FAQs
What causes code P0201 to trigger on a Acura MDX?
On the Acura MDX (3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)), P0201 is most frequently caused by Failed, open, or shorted fuel injector solenoid on Cylinder 1 or Damaged or chewed wiring harness to Cylinder 1 injector.
Where is the OBD-II port located on my Acura MDX?
On the Acura MDX, the 16-pin DLC diagnostic connector is located Driver side lower dash assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Acura MDX with code P0201?
No. Dead injector on Cylinder 1 causes immediate dead misfire, severe shaking, and unburned air/fuel delivery imbalance. Given that P0201 carries a Critical severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.