B1325 on Acura MDX: Fix & DLC Location
Factory diagnostic troubleshooting wire for fault code B1325 (B1325: Device Power 1 Circuit Voltage Below Threshold (BCM)) specifically on the Acura MDX (2022–2026, 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)).
1. Symptoms of B1325 on Acura MDX
When the Engine Control Module (ECM/PCM) on your Acura MDX (3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)) logs fault code B1325, drivers commonly observe:
2. Most Likely Causes on Acura MDX
Historical warranty claims and technical repair bulletins for Acura MDX point to the following failure distribution:
3. Step-by-Step DIY Repair Guide for Acura MDX
Interface with the diagnostic port or system console using verified scanning hardware. Record freeze-frame data, active sub-codes, and timestamps to isolate whether B1325 is static or intermittent. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Visually inspect the physical component (Main BCM Ground Wire), connector pins, and associated wiring harnesses for signs of corrosion, thermal melting, or loose grounding clips. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Measure reference voltages and resistance thresholds against manufacturer factory specifications. Replace any component failing nominal impedance tolerances. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Install genuine OEM replacement hardware or execute registry / service commands. Ensure all mounting bolts are torqued to factory specifications. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Erase the fault code from non-volatile memory. Perform a standard verification cycle (e.g. 15-minute mixed drive or system stress benchmark) to ensure monitors reset to 'Ready' state without recurrent fault flags. on the Acura MDX equipped with 3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD).
Other Common Fault Codes on Acura MDX
Frequently diagnosed powertrain, emissions, and sensor trouble codes logged on the Acura MDX:
4. Acura MDX B1325 FAQs
What causes code B1325 to trigger on a Acura MDX?
On the Acura MDX (3.5L i-VTEC V6 (290HP) / 3.0L Turbo V6 (Type S 355HP / SH-AWD)), B1325 is most frequently caused by Component aging, oxidation, or degraded internal circuit element (Main BCM Ground Wire) or Wiring harness abrasion, loose terminal pin, or ground voltage float.
Where is the OBD-II port located on my Acura MDX?
On the Acura MDX, the 16-pin DLC diagnostic connector is located Driver side lower dash assembly. Plug in any standard OBD-II scanner with the ignition in the ON position to read freeze-frame parameters.
Can I safely drive my Acura MDX with code B1325?
Caution. Limited operation permitted only to reach a nearby repair facility or backup critical personal files. Given that B1325 carries a High severity rating, we advise avoiding heavy towing or aggressive throttle inputs until sensor readings are verified.